![]() During testing I would put a second piece of acrylic on top to simulate the installation, though it was much smaller than the actual piece. The front of the acrylic (9″x3″) has the description graphic pasted to it. It is soldered onto the back of a piece of acrylic. The wire from the Arduino to the copper foil is a consistent length, about 3 inches. This was the same in the testing environment, though, and using the same ATX power supply, plugged in through a surge protector. Though 12V is routed, none of the cells are using 12V. The cables can get long, up to about 2M, but they are only handling 5V and GND. They are powered with a normal ATX power supply, and I made cables that split one connector into 5, so that each column gets power to each cell in a star network. You are quite possibly correct with the acrylic sheets and the wires.įor wires, each cell is self contained, with standard PC power supply connectors. Posted in Fail of the Week, Slider Tagged capacitive sensing, children's museum, fotw, museum, photoresistor Post navigation What have you done for child-compatible touch interfaces that are robust enough to handle uncertain environments and harsh abuse? What buttons, knobs, and other interactive elements have you used? Further, it’s a simple change to the code, and the existing circuit board will accommodate the adjustment. Some early testing indicates that it is easy to detect instantaneous change, and a trailing average and adjusting threshold make it robust enough for changing lighting conditions throughout the day. The photoresistor option has promise when the user puts their hand over the paper button the light level changes. Petition Hackaday for a better solutionįinding the problem and solving it will be a long and difficult path, especially since the museum environment is somehow and inexplicably different from the test environment.Side-by-side tests of copper tape+Arduino and AT42QT1010 had similar problems. I thought I could isolate the problem and use an existing capacitive touch sensor breakout of the AT42QT1010 hooked up to just power, but it had the exact same issue, meaning it’s either the power supply, the enclosure, or the room. Because of the way it is installed, I can’t reprogram them to adjust their sensitivity while inside the enclosure, so tweaking them post-install is not an option. ![]() The ATtiny is using the capsense library, which has features for automatic recalibration. The circuit is an ATtiny with a 2.2M resistor between two pins, one of which connects via a short wire to a soldered connection to a piece of copper tape on the underside of an acrylic piece. In one column of the table (columns share a common piece of acrylic among 5 cells), a single touch will trigger all 5. In other cells it is extremely sensitive. In some of the cells, the button doesn’t work. Maybe the room’s fluorescent lights are creating an electromagnetic field that is interrupting the sensor, or the carpet is causing static buildup that is somehow causing the midichlorians to reverse polarity and discharge through the base plate of prefabulated aluminite. Maybe it’s the power supply and a strange ground issue. It might be the second layer of acrylic contributing. Something is different about the installation from my test environment. I built a bunch of units, tested it for weeks, then installed it. Here I thought let’s use capacitive touch, put the sensor behind two layers of acrylic for protection, and then there won’t be any moving parts to break. ![]() You can read more about the Periodic Table of Motion on the project page. The second exhibit is also interactive, but in this case it’s just a simple button that turns on a thing for a while, then shuts it off. Rely on our expertise - and you'll make the best choice thanks to our advice.Buttons at toddler level are in a vulnerable position. Bürklin Elektronik: Expertise you can count on Do you need more information about electromechanical switches and pushbuttons or have a special product inquiry? Bürklin's service team is always ready to address all your concerns. Piezo pushbuttons can have different switching functions and connections for example, a differentiation is made between on-off and on-off/off-on and off pushbuttons. Specific characteristics make them ideal for use in medical devices, public input systems or industrial applications. Piezo switches are known for their long service life, reliability and freedom from maintenance. In particular, their resistance to external influences and adverse weather conditions is a relevant issue. The pushbuttons act as non-contact pressure sensors and are often used in control panels or environments that place particularly high demands on components. Pushbuttons whose functionality is based on the piezoelectric effect are called piezo pushbuttons: A mechanical action triggers an electrical pulse.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |